cover

ESP32使用microPython控制240x240彩色屏幕显示中文

王铭东老师详细讲解了讲了关于240x240屏幕的一些基础东西，我这里在原功能的基础上拓展了中文显示的功能，顺带修改了实际操作过程中程序中遇到的一些问题。

司小远

8039人浏览 · 2022-07-25 22:36:19

司小远 · 2022-07-25 22:36:19 发布

ESP32使用microPython控制1.54寸240x240彩色屏幕

王铭东老师B站视频详细讲解了讲了关于240x240屏幕的一些基础东西，我这里在原功能的基础上拓展了中文显示的功能，顺带修改了实际操作过程中程序中遇到的一些问题

一、运行效果

在这里插入图片描述

二、240x240屏幕

在这里插入图片描述

ST7789有 ST7789, ST7789V, ST7789H2等型号, 分辨率有240x204, 240x240, 240x320等多种类型, 驱动方式都是一样的.

引脚定义：

RES -> RESET复位引脚
DC -> 数据，指令选择引脚，1为数据、0为指令
CS -> Chip Select低电平有效
SCK,SCL, CLK -> SPI串行时钟信号
BL -> 背光引脚，高电平点亮屏幕，低电平关闭屏幕
SDA -> SPI串行数据输入输出信号
GND -> 电源地
VCC -> 支持3.3v和5v输入

三、硬件连接

ESP32	240x240屏幕
3V3 (or 5V)	VCC
GND	GND
GPIO18	SCL
GPIO23	SDA
GPIO2	DC
GPIO5	CS
GPIO22	BL
GPIO17	RES

四、驱动下载

4.1、驱动下载地址

st7789py.py：https://github.com/russhughes/st7789py_mpy
修改后的代码及附件下载地址：https://github.com/LC044/MCU/tree/main/ST7789

4.2、bug修改

使用原作者驱动的时候发现屏幕不亮，对原驱动代码稍加修改能够成功显示画面

将204、205行代码注释掉

#self.hard_reset()
#self.soft_reset()

后面加上三行代码

self.cs.init(self.cs.OUT, value=1)
self.dc.init(self.dc.OUT, value=0)
self.reset.init(self.reset.OUT, value=1)

215、216行代码替换成

if backlight is not None:
    #backlight.value(1)
    self.backlight.init(self.backlight.OUT, value=1)

4.3、支持中文显示（还不完善）

st7789类中增加三个方法

显示16x16大小的中文

    def _text_gb16(self, font,size, text, x0, y0, color=WHITE, background=BLACK):
        for char in text:
            if (x0+font.FONT['WIDTH'] <= self.width and y0+font.FONT['HEIGHT'] <= self.height):
                for line in range(2):
                        idx = line * 16
                        buffer = b''
                        for x in range(16):
                            for i in range(8):
                                buffer += struct.pack('H',color if font.FONT[char][idx+x] & _BIT[7-i] else background)
                        self.blit_buffer(buffer, x0, y0+8*line, 16, 8)
                x0 += font.WIDTH

显示24x24大小的中文

    def text_gb24(self, font,size, text, x0, y0, color=WHITE, background=BLACK):
        for char in text:
            if (x0+font.FONT_24['WIDTH'] <= self.width and y0+font.FONT_24['HEIGHT'] <= self.height):
                for line in range(3):#分成3次显示
                    idx = line * (font.FONT_24['SIZE']//3)
                    buffer = b''
                    for x in range(font.FONT_24['SIZE']//3):
                        for i in range(8):
                            buffer += struct.pack('H',color if font.FONT_24[char][idx+x] & _BIT[7-i] else background)
                    self.blit_buffer(buffer, x0, y0+8*line, font.FONT_24['WIDTH'], 8)
                x0 += font.FONT_24['WIDTH']

显示32x32大小的中文

    def text_gb32(self, font,size, text, x0, y0, color=WHITE, background=BLACK):
        for char in text:
            if (x0+font.FONT_32['WIDTH'] <= self.width and y0+font.FONT_32['HEIGHT'] <= self.height):
                for line in range(4):
                    idx = line * (font.FONT_32['SIZE']//4)
                    buffer = b''
                    for x in range(font.FONT_32['SIZE']//4):
                        for i in range(8):
                            buffer += struct.pack('H',color if font.FONT_32[char][idx+x] & _BIT[7-i] else background)
                    self.blit_buffer(buffer, x0, y0+8*line, font.FONT_32['WIDTH'], 8)
                x0 += font.FONT_32['WIDTH']

显示48x48大小的中文

    def text_gb48(self, font,size, text, x0, y0, color=WHITE, background=BLACK):
        for char in text:
            if (x0+font.FONT_48['WIDTH'] <= self.width and y0+font.FONT_48['HEIGHT'] <= self.height):
                for line in range(4):#分成4次显示
                    idx = line * (font.FONT_48['SIZE']//4)
                    buffer = b''
                    for x in range(font.FONT_48['SIZE']//4):
                        for i in range(8):
                            buffer += struct.pack('H',color if font.FONT_48[char][idx+x] & _BIT[7-i] else background)
                    self.blit_buffer(buffer, x0, y0+12*line, font.FONT_48['WIDTH'], 12)
                x0 += font.FONT_48['WIDTH']

text方法修改

    def text(self,font,size, text, x0, y0, color=WHITE, background=BLACK):
        """
        Draw text on display in specified font and colors. 8 and 16 bit wide
        fonts are supported.
        Args:
            font (module): font module to use.
            text (str): text to write
            x0 (int): column to start drawing at
            y0 (int): row to start drawing at
            color (int): 565 encoded color to use for characters
            background (int): 565 encoded color to use for background
        """
        if font.flag == 'gb16':
            self._text_gb16(font,size, text, x0, y0, color, background)
            #print('gb16')
        elif font.WIDTH == 8:
            self._text8(font, text, x0, y0, color, background)
        else:
            self._text16(font, text, x0, y0, color, background)
            #print('abc16')

4.4、获取中文字体

在线取模网址：在线点阵取模_暮光小猿wzt (scraft.top)

首先选择需要的字体大小，底下参数选择反转位序

在font_gb_16x16.py中添加字典

示例格式：（必须标明字体宽高和每个字的字节大小）

FONT = {
    'HEIGHT':16,
    'WIDTH':16,
    'SIZE':32,
    '当':[0x01,0x00,0x21,0x08,0x11,0x08,0x09,0x10,0x09,0x20,0x01,0x00,0x7f,0xf8,0x00,0x08,0x00,0x08,0x00,0x08,0x3f,0xf8,0x00,0x08,0x00,0x08,0x00,0x08,0x7f,0xf8,0x00,0x08],
    '前':[0x10,0x10,0x08,0x10,0x08,0x20,0xff,0xfe,0x00,0x00,0x3e,0x08,0x22,0x48,0x22,0x48,0x3e,0x48,0x22,0x48,0x22,0x48,0x3e,0x48,0x22,0x08,0x22,0x08,0x2a,0x28,0x24,0x10],
    '天':[0x00,0x00,0x3f,0xf8,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0xff,0xfe,0x01,0x00,0x02,0x80,0x02,0x80,0x04,0x40,0x04,0x40,0x08,0x20,0x10,0x10,0x20,0x08,0xc0,0x06],
    '气':[0x10,0x00,0x10,0x00,0x3f,0xfc,0x20,0x00,0x4f,0xf0,0x80,0x00,0x3f,0xf0,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x0a,0x00,0x0a,0x00,0x06,0x00,0x02],
    '阴':[0x00,0x00,0x7d,0xfc,0x45,0x04,0x49,0x04,0x49,0x04,0x51,0xfc,0x49,0x04,0x49,0x04,0x45,0x04,0x45,0xfc,0x45,0x04,0x69,0x04,0x52,0x04,0x42,0x04,0x44,0x14,0x48,0x08],
    }

注：不要加载太多字体，否则会显示内存不足。需要大量字库的话可以将字节码写入文件里，不要用python字典存储，python字典的散列表很耗费空间。

五、示例程序

首先将字体文件下载到esp32的flash里，这里我放在了esp32的package文件夹里

from machine import Pin, SPI
from package import st7789py as st
from package import vga1_16x32 as font
from package import font_gb_16x16 as font_gb
import time

class Display():
    def __init__(self):
        self.tft = st.ST7789(SPI(2, 10000000), 240, 240, reset=Pin(17), dc=Pin(2), cs=Pin(5), backlight=Pin(22), rotation=0)
        self.WHITE = st.color565(255, 255, 255)#BRG
        self.BLACK = st.color565(0, 0, 0)
        self.RED = st.color565(0, 255, 0)
        self.GREEN = st.color565(0, 0, 255)
        self.BLUE = st.color565(255, 0, 0)
        self.YELLOW = st.color565(0, 255, 255)
        print(self.RED,self.GREEN,self.BLUE)
        self.last_hour = 0
        self.last_minute = 0
        self.last_second = 0
        self.last_year = 0
        self.last_month = 0
        self.last_day = 0
        self.init_show()
    def init_show(self):
        '''
        初始化显示画面
        '''
        self.tft.text_gb48(font_gb,32, ':', 20+24*2, 100, self.WHITE, self.BLACK)
        self.tft.text_gb48(font_gb,32, ':', 20+24*5, 100, self.WHITE, self.BLACK)
        self.tft.text_gb48(font_gb,32, '00', 20, 100, self.WHITE, self.BLACK)
        self.tft.text_gb48(font_gb,32, '00', 20+24*3, 100, self.WHITE, self.BLACK)
        self.tft.text_gb48(font_gb,32, '00', 20+24*6, 100, self.WHITE, self.BLACK)
        self.text_gb('小雨')
        self.text('hello world!')
    def text_gb(self,text):
        self.tft.text_gb32(font_gb,32, text, 0, 0, self.WHITE, self.BLACK)
    def text(self,text):
        self.tft.text(font,32, text, 0, 50, self.GREEN, self.BLACK)
    
    def show_time(self,t):
        '''
        显示时间
        '''
        year = t[0]
        month = t[1]
        day = t[2]
        hour = t[3]
        minute = t[4]
        second = t[5]
        ti = "{:0>2d}:{:0>2d}:{:0>2d}".format(hour,minute,second)
        #print(ti)
        if hour != self.last_hour:
            self.tft.text_gb48(font_gb,32, '{:0>2d}'.format(hour), 20, 100, self.BLUE, self.BLACK)
            self.last_hour = hour
        if minute != self.last_minute:
            self.tft.text_gb48(font_gb,32, '{:0>2d}'.format(minute), 20+24*3, 100, self.RED, self.BLACK)
            self.last_minute = minute
        if second != self.last_second:
            self.tft.text_gb48(font_gb,32, '{:0>2d}'.format(second), 20+24*6, 100, self.GREEN, self.BLACK)
            self.last_second = second
        #self.tft.text_gb48(font_gb,32, ti, 20, 100, self.WHITE, self.BLACK)
        
    def run(self):
        while True:
            t = time.localtime(time.time())
            #if t[5]%2==0:
            self.show_time(t)
            time.sleep(0.5)
            #for i in range(65536,100):
            #    self.tft.text_gb32(font_gb,32, '雨', 100, 150, i, self.BLACK)
        
    def __del__(self):
        pass
D = Display()
D.run()

运行结果见开头

腾讯云开发者社区

腾讯云面向开发者汇聚海量精品云计算使用和开发经验，营造开放的云计算技术生态圈。

更多推荐

cover

动物识别系统 python实现+UI

腾讯云开发者社区

Linux下安装MySQL8.0(超详细)

Linux下安装MySQL8.0(超详细)

腾讯云开发者社区

cover

安卓手机如何连接苹果电脑

腾讯云开发者社区

所有评论(0)

查看更多评论

司小远

已为社区贡献2条内容